Category: Blog

The basis of the shower is the floor of the cabin shower. Usually this part has a height of 5 inches (12.7 cm) and a drain and is made ​​to fit just within the walls of the shower. Some measures are standard for shower base; however, they can be manufactured as shower pan of any size.

Standard full shower

A complete standard shower usually measures 30 inches wide (76 cm) by 60 inches (1.5 m) long. This fits standard base in the bath or showers any standard home with some modifications in the shower walls. As always, flush strips which are long wood strips that function as wedges can be used to adjust the shower base in areas that are not exactly square.

Largest full shower

Some areas for the shower are larger than others. In larger showers, dimensions extend to the 42-inch (1 m) wide by 60 inches (1.5 m) long. The bathrooms and medium showers measure 36 inches (91 cm) wide by 60 inches (1.5 m) long, The base may be wider for those seeking to place a whirlpool Jacuzzi or larger. The basis of this long standard size will fit in these predetermined areas when a tub is not installed.

Square bases

Many shower bases are smaller than full made to occupy the space normally occupied by a tub. These showers are built into bathrooms with limited space and may even occupy the space of what was once a closet. The square bases are usually from 32 (81 cm) by 48 inches (1.2 m) inches. The size depends around the shower and the available space in the bathroom. Find square bases, angled bases and even circular bases. Common sizes are 36 inches (91 cm) by 36 inches (91 cm) and 48 inches (1.2 meters) by 36 inches (91 cm).

Round bases

Some bases have a rounded end. This configuration makes sense in small bathrooms where space is precious. A square base occupies more space than circular base and, as people usually do not use both corners, they do not provide much comfort. Round bases are standard size, with a width from 30 inches (76 cm) to 48 inches (1.2 m) on the sides; on the late side, the base is arched. The size depends on the width of the opposite side to the edge of the rounded side of the base.

A quarter of bathroom, small one does not mean you have to give up the luxury of installing a soaking tub, which is much deeper than standard tubs. The soaking tubs allow you to immerse the body in the water, leaning comfortably back in the bathtub without having to slide down in a difficult and uncomfortable situation.

Corner tubs

Use the corner of your bathroom for a corner bath, which may seem extravagant and luxurious, while occupying less space. Corner bathtubs can actually make the room appear larger and standing in the corner take up less visual space. The tubs may also provide up to 1 foot (30 cm) of space due to additional corner bath tub position. Whirlpools, armrest, corner seats and various decorative finishes are available.

Claw foot tubs

Claw foot tubs come in a variety of styles and can add an antique look to your small bathroom while taking less space due to visual design of separate bathtub. Supplements will allow you to convert your claw foot tub in a shower, which can eliminate the need for a separate shower and save more space. The tub may include extreme to rest on both sides with a drain in the center to create a comfortable bath for two or a drain at one end with a design to rest at the other end.

Deep tubs

Readily available in stores and home improvement warehouse stores, regular acrylic bathtubs come in smaller sizes and varying depths, allowing you to choose a bathtub that fits your small bathroom and meets your needs. Some baths have additional options such as water jets, to create the bathing experience you want.

Bathtubs with door

Bathtubs with door take up much less space than traditional bathtubs because they are about the same size as a standard shower cubicle. The bathtub has a door on the side that lets you literally get in the tub. Most models include a seat. The drawback of the tubs with door is that you get into the tub before opening the water and wait until it is fully drained before you can out of the bath.

Woodworking is a relaxing and creative activity. You can do small jobs for short periods of time, making it perfect for beginners or carpenters to work those who teach these children or adolescents with little or no experience. Small woodwork is ideal gift for anyone.

Aviary

The aviaries are small jobs to make wood. The website Family Fun design features a birdhouse to build on table. If you have certain species of birds for which you want to build the aviary, as joyous ducks, robins, wrens and swallows; birdhouses have to be built of different types or sizes. All Woodwork Online site gives some examples of wooden birdhouses. In the handicraft shops you can find kits with instructions and tips. They are also available in online stores, as Finish Carpentry Help Online.

Shelf

The shelves are easy to build and serve for a purpose in a house, shop or office. You can make a small shelf to put on a sink. An example of a project is shown to make a small corner shelf on the site Home Shaving Guide Online. To do this, you just need a round plywood table of 24 inches (60 cm), a power tool and a table saw.

Memory Box

Memory boxes are wooden handicrafts that you can give away. They may be round or rectangular. There are plans to make memory boxes available for free at many online stores as Woodworkers Workshop Online. Request the master carpenter from your local high school to make you plans for a box for simple memories. If you are a novice carpenter, ask the teacher some tips to start your project.

Picture frame

The tools needed to make a picture frame are a saw, grooving and polishing. The model is in the Amateur Woodworker Online page is made of hard maple. This website explains the process for making picture frame step by step. You can make frames in a few hours.

Constant exposure to water and sedimentation or displacement of the walls of the bathroom can make grout around the tiles to crack. The slurry in this state must be repaired to keep water away from the cracks. Over time, the water may damage the structure and decompose the underlying layers. This will trigger repairs which could have been avoided than repairing the broken grout. This type of repair is a job that you can do yourself without hiring anyone.

Instructions

1. Cut the grout lines with a saw for that purpose. This is a hand tool that has a narrow leaf diamond. The blade is designed to fit inside the grout lines between the tiles. Spend the saw back and forth as much as you can about the old grout.
2. Slurry sucked pieces with an industrial vacuum cleaner and wet the tiles with a damp cloth.
3. Fill a bucket with 1 gallon (3.78 l) with water to a depth of no more than 1 inch (2.54 cm). Slurry poured into the bucket of a little at a time. Mix the grout in the water with a spatula of 3 inches (7.62 cm). Continue adding water slurry until slightly thicker than a cake mix. The grout should be thick enough to stay on the spatula but as not to spread it.
4. Spread grout space between the tiles with a leveling grout. Do not cover larger than 3 by 3 feet (0.9 by 0.9 m) areas. Keep the leveling to 45 degrees and drag on the tiles. Collects excess grout with a spatula and place the surplus back into the bucket.
5. Fill a bucket of 5 gallons (18.90 l) with hot water. Dip the sponge in water and wring. Hold the sponge flat on the tile, passing over the grout lines. Apply gentle pressure to the sponge and pass through the grout lines to soften. Spend the sponge horizontally by horizontal grout lines and vertically by vertical grout lines.
6. Rinse the sponge often and repeat steps five and six for completion of the grouting.

Tips & Warnings

• If the grout is old and stained, replace the entire shower grout. Cut the grout lines with the specific saw deep enough so that it can contain the new grout.
• You can use a grinder of 4 1/2 inches (11.43 cm) with diamond wheel carbide to the extent that there is enough space between the tiles. Be careful if you use this method to not get too close to the tile, you could break it.
• Do not place grout larger than 3 by 3 feet (0.9 by 0.9 m) areas. The grout dries quickly and is extremely difficult to remove once it has dried.

Many owners ignore the smell of wet basements, but are something that should not be done. That smell means there are fungus, caused by excessive humidity, low light and poor air circulation. Fungi grow on most surfaces of a basement and identify because they are black or white. Try these odors immediately to avoid exposing yourself to harmful fungi and mold spores. According to the Allergy Consumer Review (Review of allergic consumers), “exposure to the smell of moisture is a risk to health because it cause chronic allergies, chronic sinusitis and asthma.”

Instructions

1. Open all basement windows to make the smell of damp leave, if you have installed walls extractors. Otherwise, place electric fans in front of windows.
2. Sprinkle chlorinated lime over all the carpeted areas of the basement and wear gloves and a dust mask. Leave chemicals in dust on the carpet until the musty smell dissipates.
3. Vacuum the carpet throughout. Put 1 cup of bleach in 1 gallon of water in a bucket.
4. Spend this solution on all surfaces of cement floor with a loofah sponge. This solution also cleans all concrete walls using a sponge.
5. Throw the dirty solution and rinse the bucket with water once you have finished cleaning the floor and walls. Fill the bucket with fresh water.
6. Pass the ground water to remove the bleach solution. Rinse the walls with water using a clean cloth.
7. Clean the walls and floor thoroughly with clean dry towels to prevent moisture from forming. Connects a pair of dehumidifiers to remove all moisture from the air.

Tips & Warnings

• You can replace the sodium hypochlorite bleach.
• Use gloves and dust mask during the cleaning process to prevent touching and breathing chemicals.

You walked with a cup of coffee and suddenly stumbled and spilled all its contents on the carpet. These spots are unsightly and make the carpet look old and dirty. Do not worry! You can clean up the mess immediately. Follow these steps to remove the stain.

Instructions

1. Dry the area with a white cloth and clean to absorb as much liquid as possible. Start from the part outside of the stain to prevent it from spreading.
2. Mix one teaspoon of mild dishwashing liquid detergent with one cup of warm water.
3. Apply the detergent solution on the area with a sponge. Dry again with a white cloth.
4. Mix 1/3 cup white vinegar with 2/3 cup of warm water.
5. Apply the vinegar solution with a sponge. Dry with a clean white cloth.
6. Clean the area with a sponge and clean water. Dry with a clean white cloth.

Tips & Warnings

• Using a clean white cloth that you avoid colorfast cloth dyeing on the carpet.
• Avoid rubbing or scrubbing, this will cause the stain to spread.

To improve the aesthetic qualities of assembling a door, many manufacturers now in modern days are producing knobs that come with false plate’s adornment. This plate covers the operational assembly of the door handle and the screws. The end result is a design streamlined, but nevertheless, the difficult access to the screws to remove the handle until you knows how to remove the trim plate.

Instructions

1. Examine the edge of the metal plate handle on the inner side of the door, and recessed for hidden screw. This screw holds the board in place, and usually is sunk into the side of the plate, making it difficult to see it at a glance.
2. Find an Allen wrench that fits the screw, trying with each assembly until it fits one. Insert the tip of the key in the screw, and turn the clock backwards until the faceplate slide freely. It may be that sometimes the door handle use other screw as one Philips head. If so, use a Philips screwdriver instead of an Allen wrench.
3. Remove the plate motif of front door. The faceplate can get away completely, depending on the design of the door handle; if not, turn the plate until the screws of the base are accessible, and then use a Phillips screwdriver to remove them.

Tips & Warnings

Some designs knobs can take a bolt instead of a screw. If that is the case, press the pin inwards with any thin object, and pull the plate out. To remove the entire handle assembly, also remove the two screws located on the inside of the door, on each side of the lock.

One of the most important steps to build a concrete wall is to have enough material for the project. There is a standard formula used to determine how much concrete is needed; when in doubt, it is better to ask for a little more than you think you need your project.

Measures

Know the height, width and thickness of your wall to calculate the necessary amount of concrete. When the measurement is not an exact fraction of an inch, it is better to round up.

Calculation formula

Multiply the height, width and depth in feet. For example, if you want to make a wall of 6 feet (1.83 m) high, 10 feet (3.05 m) wide and 0.34 feet (about 4 inches or 10.16 cm) thick, multiplies these three numbers for a Total of 20.4 cubic feet (0.58 cubic meters). Concrete is sold in cubic yards, so you’ll need to divide the calculation by 27 (the number of cubic feet in a cubic yard). In the above example, you divide 20.4 by 27 for a total of 0.75 cubic yards (0.57 cubic meters).

Concrete Extra

Having calculated how many cubic yards of concrete is need, you should add between 5 and 10 percent bonus to your calculation. This ensures that sufficient concrete have if a spill or other errors generate a loss of material.

A unit split air conditioning unit has a wall mounted inside a house or apartment and another unit for air and cool. The indoor unit delivers air only, so do not make much noise (see Reference 1). A Mitsubishi split AC unit should be cleaned to continue operating conditions as other units like. Filter cleaning is the largest for the unit (see Reference 2) consideration.

You will need

• A mild detergent
• A cloth
• A vacuum cleaner

Instructions

1. Remove the front panel of the unit split air conditioning Mitsubishi. Dampen a cloth and pass it through the panel to remove any residual dust or accumulated dirt.
2. Remove the air filter unit pulling a small handle. Vacuum the filter to remove any surface dust. Moisten the filter in a solution of one teaspoon of mild detergent and warm water for 10 to 15 minutes. Rinse with clean water until the filter clean pass. Let it air dry in the shade before replacing the unit.
3. Remove the air cleaning filter. Soak it in a solution of two teaspoons of mild detergent in warm water for 15 minutes. Rinse with clean water. Let it air dry in the shade before putting it back in split unit.
4. Replace the front panel.

How to clean a crystal chandelier. Your delicate chandelier will glow more brightly without all that dust and dirt. Here’s how they shine again.

You will need

• Spray Bottles
• Cleaning Cloths
• Ammonia
• Cleaning Fluids for spiders
• Isopropyl Alcohol
• Masking Tape
• Distilled water
• Sandwich Bags
• Rubber bands

Instructions

1. Connect the alternative lighting nearby (and you will not be able to use the lamp for lighting while you’re cleaning).
2. Turn off the power to the lamp from the wall switch. Place a piece of tape over the switch on the wall so no one can accidentally turn it on while you’re working.
3. Cover the bulbs point up with bags for sandwiches. Secure the bags with rubber bands.
4. Put a spider plugs below.
5. A solution of a mixture of isopropyl alcohol and three parts of ammonia in distilled water. Or, if you want to mix your own cleaner, buy a cleanser especially for spiders in a lighting store. Put some solution in a spray bottle.
6. Sprinkle each side of the device with the cleaner, avoiding wires and other electrical components.
7. Allows dripping crystals dry. If your lamp is too dirty to use this method of cleaning drip, you have to hand wash each crystal individually with the cleaning solution.
8. Bring plastic bags lights once the crystals are dry, and clean the mounting lights and other parts that are not made of glass with a soft cloth moistened with cleaner.
9. Let it all apply to dry overnight before restarting.